How To Refinish Hardwood Floors (2024)

1

Prep Floor

The first step in learning how to refinish wood floors is preparing your floor and room properly.

• Perform a water droplet test to quickly reveal your floor’s condition. If you splash water droplets on the floor and they soak in immediately, your floor needs refinishing. If the droplet beads on the floor, it may only need to be cleaned and polished.
• Move the furniture and pull up any carpeting or rugs in the room.
• Hammer down protruding nails. Find protruding nails by sliding the blade of a putty knife across the floor.
• Check for squeaks and secure loose floorboards with finishing nails.
• Remove debris on the floor with a vacuum cleaner or mop.
• Seal air vent covers to prevent dust caused by sanding from getting into your ductwork and your home. Use plastic sheeting to seal doors to keep dust from the rest of the house.

2

Remove Base Moulding

Before floor refinishing with a sander, you should pull up the shoe base moulding along where the floor meets the wall.

• Pry the moulding with a pry bar. Consider using a piece of scrap wood to protect the baseboard.
• Number or otherwise label each piece as you remove it to make it easier to put it back after refinishing the floor.

Tip: If the room has no shoe base moulding, either remove the base moulding or take care not to damage the wall when operating the sander.

3

Rough-Sand the Floor

You'll use different sanding steps as you learn how to refinish a hardwood floor. Start by rough-sanding the floor to eliminate the scratches and stains from a hardwood floor. Keep in mind this step will probably not remove deep gouges or discoloration.

• Begin by using a drum sanderor belt sander with the grain along the length of the boards.
• Work the drum sander back and forth over 3- to 4-foot lengths.
• Use overlapping strokes by at least 1/3 the belt width to remove scratches.
• Start with coarse sandpaper of 36 to 40 grit, progress to a medium 60-grit paper and finish with a finer 100 grit. Do not skip the progression from coarse grades to finer grades.
• Replace the abrasive belt after sanding about 250 square feet for most effective results.
• Sweep and vacuum the flooring to remove dust and debris between sanding with different grades of grit.

Tip: Practice using the drum sander on an old sheet of plywood until you’re comfortable operating it on your floors.

4

Sand Edges and Corners

Use a floor edger or small orbital sander to sand corners, edges and small areas such as closet floors, bathrooms or stairs.

• As with the drum sander, start with course-grit paper and then move to finer grades.
• If the flooring has small areas that even the edger cannot reach, use a scraper and some 80- and 100-grit sandpaper to remove the old finish by hand.

Tip: An edger can be difficult to control, so practice your technique on scrap wood first.

5

Screen Sand Floor

Next, use a floor buffer fitted with a fine-grit screening pad to “screen-sand” the flooring.

This type of sanding will level minor unevenness left by the drum sander and edger as well as buff away sanding scratches. This fine-detail work can make your DIY project look more like a professional job.

• Be prepared for the buffer to swing to the right or left depending on how you position the handle.
• Make broad arcs across the floor to get a smooth surface.

6

Remove All Dust

7

Apply Wood Stain or Sanding Sealer

If you want to change or improve the floor color, apply a stain.

• Choose an interior wood stain based on the color you desire and the type of hardwood flooring you have.
• Apply the stain with a foam applicator pad in the direction of the wood grain.
• Work one manageable area at a time, such as four square feet.
• Many manufacturers recommend removing excess stain as you go, usually a few minutes after application.
• Use clean cotton cloths or paper towels to remove excess stain. Some finishers prefer wiping the floor with a cotton cloth wrapped around a dry applicator pad.
• Allow the stain to dry according to directions before applying the finish.

Tip: If you choose not to stain, apply a sanding sealer before the polyurethane finish.

8

Apply Wood Finish

Choose a protective coat of wood finish or oil. Things to know:

• Water-based polyurethane wood finishes or lacquers dry quickly, which can pose challenges during application.
• Oil-based polyurethane wood finish dries more slowly and provides a smooth coat. However, the fumes may require wearing a respirator during application.
• Popular wood oils include Danish oil, teak oil, tung oil, cedar oil, ipe oil and mineral oil for wood.

Follow these steps when applying the finish.

• Apply the finish with a lamb’s wool applicator in smooth, even lines. Avoid drips.
• Consider three coats of oil-based finish or four coats of water-based finish.
• When each coat dries, sand the floor lightly with 220-grit paper or #000 steel wool. Many finishes take 24 hours to dry.
• Vacuum up the dust and apply the subsequent coat.
• When the finish is dry, reattach any moulding.

Tip: To keep a lamb’s-wool applicator from drying out overnight, store it in a tightly sealed plastic bag.

9

Wood Floor Refinishing Tips

When refinishing hardwood floors:

• Eachtime you’re ready to change grades on the drum sander, make sure you use the edger using the same grade sandpaper to keep the entire floor sanded at a uniform consistency. For example, use the drum sander at 60-grade paper, then the edger with 60 grade, before changing to 80 grade.
• Most drum and edger sanders have built in vacuums and dust bag systems to reduce dust emissions.
• After sanding, fill in holes in the floor with wood putty or wood filler.
• Spot test the stain or finish to see what it looks like on the floor before applying a coat.
• Apply the stain or finish so your final steps are at the exit door and you don’t have to track through a wet floor.
• When returning the furniture to room, place felt pads on the feet to prevent them from scratching the floor. Avoid dragging furniture across the floor.
• Flooring experts estimate that hardwood floors can be sanded for refinishing up to 10 times, depending on the thoroughness of the sanding and the level of wear and tear on the floor. Situations differ, but you may not be able to refinish your hardwood floor more than 10 times.

10

Floor Refinishing Safety

• Always wear a dust mask, safety goggles and ear protection when using a drum sander.
• If using a drum or upright floor sander, make sure to review and follow the manufacturer’s instructions carefully to avoid injury or damaging your floor.
• Cover home vents and grates to help prevent sanding dust from circulating through your home.
• Be sure to work in well-ventilated rooms when sanding or applying stain or finish. If possible, open windows and exterior doors.
• Store and dispose of oil-soaked rags properly. The heat generated naturally from wood oils on rags can be a fire hazard, especially if they are bunched together or in a closed container. Hang the rags outside, away from any structures. Allow them to dry thoroughly before disposing of them.