How to Scuff Sand: 10 Steps (with Pictures) - wikiHow (2024)

Explore this Article

Co-authored byVarga Gulshani

Last Updated: April 20, 2024References

Download Article

1. 1

   Put on a pair of goggles and a dust mask. If possible, move to a well-ventilated area, or at the very least, open up a window. Sanding creates a lot of dust. Some surfaces contain coatings (i.e.: polyurethane) that can be hazardous to your health and lungs.

   • If you are going to scuff sand walls, check to see that the paint does not contain lead. If the paint contains lead, do not sand it; use a de-glosser instead.
2. 2

   Choose a fine-grit sandpaper. There are lots of different grits that fall into this category, so choose something based on the type of scuffing you are doing. In most cases, you will scuff sand a bare surface before applying anything, and sand again between coats of paint or sealer. Here is what you should look for:^[3]

   • If you are scuffing bare wood, or another surface, in preparation for priming, painting, and/or staining, you will need something between P120 and P150.
   • If you are scuffing between coats of paint or sealer, choose something between P180 and P220.
   • If you are sanding between coats of varnish and need a high-gloss finish, look for a P320 grit.^[4]
   • For high-gloss varnish, polyurethane, and lacquer finishes, wet sand with P600 or P800.

   Advertisem*nt

3. 3

   Consider other options besides sandpaper. There are buff sanders, sanding blocks, and sanding sponges. A piece of sandpaper or a sanding block will be suitable for most surfaces, but it may not be the most efficient for curves or tight corners. Here are some options you should consider:

   • Floors: Buffer and sandpaper.
   • Rounded curve: use a sanding sponge.
   • Tight corners: choose a sander with a pointed tip or a fine wire brush.
   • Steel wool comes in a variety of grades and can be used in place of sandpaper.
   • Sandpaper and finish sanders are always your best bet, especially when compared to liquid sanders.^[5]
4. 4

   Fold or wrap the sandpaper, if necessary. A flat sheet of sandpaper will work just fine on flat surfaces, but there are a few things you can do to make it even more efficient, based on the job that you are doing. Here are a few suggestions:

   • Small items or corners: cut a sheet of sandpaper into quarters, then fold each quarter into thirds, lengthwise.^[6]
   • Concave curve: wrap the sandpaper around a 1-inch (2.54-centimeter) wide dowel. Secure it with double-sided tape or glue.
   • Walls: attach your sandpaper or sanding block to a pole. You can find special attachments in a hardware store.^[7]

Advertisem*nt

Download Article

1. 1

   Consider marking up bare surfaces with a pencil. You don't absolutely have to do this, but it is a good way to judge how much you've sanded. Use a pencil to draw squiggles on the surface to be sanded.

2. 2

   Lightly sand the surface. Use a light touch and do not press down too hard, otherwise, you will get scratches in your work. If you see scratches, wet the surface and use a lighter touch or switch to a finer grit. Always work with the grain, not against it, and do no more than three passes on edges and corners.

   • If you are sanding a floor, sand the entire floor with a buffer. Go with the grain, and overlap each row by 6 inches (15.24 centimeters).
3. 3

   Clean the dust off of your work. Dust small pieces off with a dry paintbrush first, then wipe it clean with a tack cloth. If the piece is especially dusty, wipe it down with a damp cloth instead, then let it dry completely.^[8] Clean larger pieces with a vacuum or an air hose first, then wipe them down with a tack cloth as well.^[9][10]

   • If you sanded the floor, wait about 10 to 15 minutes for the dust to settle before vacuuming it up.
   • If you sanded a wall in preparation for painting, wipe it down with a damp cloth.^[11]
4. 4

   Check the surface for un-sanded patches. A painted or primed surface is the easiest to tell, because it will look chalky. Other surfaces, such as bare wood or varnished surfaces, may be harder to tell. Run one hand over the surface and sand out any areas you missed with the other. Here are some tips:

   • Rub a sock over bare wood. If the sock snags, you have a rough spot that needs more sanding.
   • Look at varnished pieces from an angle in a well-lit area. There should be no shiny spots.^[12]
5. 5

   Re-sand the surface, if needed, then wipe it clean again. You may have to do this a few times until you achieve the finish you want. Bare wood surfaces should feel smooth, without any snags. Primed or painted surfaces should look chalky, while varnished surfaces should look matte.

   • Do not over-sand, especially for primed, painted, or varnished surfaces. You do not want to sand through to the bare surface.
   • If you are sanding a floor, go back along the edges with 180-grit sandpaper, 4 to 6 inches (10.16 to 15.24 centimeters) from the baseboards.
6. 6

   Apply your paint and/or varnish as usual. If you are working with just varnish, consider sanding between the different coats of varnish as well; be sure to let each coat dry first, however. You could also apply two coats of varnish before scuff sanding it. The first coat will fill in any gaps, while the second will smooth things out.^[13]

Advertisem*nt

Expert Q&A

Ask a Question

Tips

Thanks for submitting a tip for review!

Warnings

Things You'll Need

5 votes - 100%